Internal 9/16 L H, 5 8 &Deg, Seal;External 1-1/8 T
Input Water Degree
<40°
Transport Package
Carton
Trademark
Megajet
Origin
China
Production Capacity
1000units /Year
Product Description
Equipment Introduction
Megajet high pressure cleaning machine is water as the working medium, usually, the power drive pump through the water to complete a suction, discharge process, the ordinary water into high low flow rate of water, and then transported to the high pressure pipeline, so that it with a certain amount of energy to reach the high pressure nozzle. The aperture of the high pressure nozzle is much smaller than the diameter of the high pressure pipeline, so the water reaching the high pressure nozzle must be accelerated to pass through the nozzle. In this way, the nozzle can convert water at a high and low velocity into a low pressure and high velocity jet. The ejected high-pressure water jet tangentially or positively impacts the surface of the cleaned object, and constantly shocks the cleaned surface, making the dirt fall off. Therefore, the use of a high-pressure cleaning machine is a physical cleaning method.
Surface Cleaning Rotary Nozzle
MEGAJETFour-hole rotating nozzle is a flat cleaning nozzle. The highest working pressure is 2 8 0 0 B A R, the lowest is 1500 BAR, the higher the pressure, the higher the nozzle speed. Its flow rate range is 1 2 L-1 8 L / min. The connection mode is internal 9 / 1 6 LH, 5 8° cone seal, and external 1-1 / 8 threaded connection. Its internal deceleration mode is magnetic damping deceleration mode, the sealing mode is high pressure sealing, fixed mode is, thread fixed, balance mode is bearing balance, magnet is high temperature resistant magnet, lubrication mode is grease lubrication, it is recommended to choose high temperature grease. MEGAJET The standard nozzle is equipped with: 1 nozzle rotating body, 1 four-hole surface nozzle, 4 surface nozzle nozzle (0.38mm), 1 surface nozzle cover (stainless steel), 3 high pressure seals, 3 high pressure sealing seats.
Instructions * Recommend a small amount of wearing parts, use grease and special tools. * It is recommended to replace the high pressure seal each time when disassembly, otherwise it is easy to produce repeated disassembly action. Therefore, it is recommended that when the number of high pressure seal is less than 1 group, the high pressure seal components should be purchased in time for replacement and maintenance. * When using the nozzle, it is necessary to replace different large and small nozzles according to the different scale of the blow, so it is recommended to use two to three sets of nozzles as backup. For example, if you need to hit a single scale, it is recommended to equip 2-3 sets of nozzles of the same size as backup. * The head shield recommends two spare times for each head. The cover can protect the nozzle from backsplash and extend the service life of the nozzle.
Removing and Installing MEGAJET During the disassembly and installation of the rotary nozzle, special disassembly tools should be equipped. Anti-occlite should be applied to the thread connection parts. The locking moment is 50N / m. Overforce locking and unlocking are prohibited. The copper sleeve top moment is 12 N/m. During the disassembly and installation of the rotating nozzle, the basic cleaning of the disassembly site shall be ensured. During the disassembly and installation of the rotating nozzle, prohibit the knock and overforce disassembly. The whole nozzle component is equipped with special disassembly tools for high pressure seal, and no new purchase is required. In the case of any combination of accessories, it is not equipped with special tools and nozzle toolbox.
Operation Instructions Using a four-hole rotating nozzle should be equipped with a short gun, which should be equipped with a overflow valve or a pressure cut-off mechanism to release pressure quickly. When used, the overall length of the shotgun (including the length of the flat head itself) must be greater than the length of the operator's arm to the heel to ensure that the operator does not accidentally injure the foot when using the washer. It is recommended that the operator weighs at least three times the thrust produced in normal working conditions. Select the appropriate nozzle model to install on the nozzle, and it is recommended to use the antiocclusal agent on the nozzle thread to prevent the biting between the nozzle and the nozzle. Attach the four-hole rotating nozzle to the shotgun. Before connecting the high pressure hose and the short gun, wash the high pressure hose to ensure that there is no dirt in the high pressure hose and affect the normal use of the product. After the high pressure equipment is ready, the overflow and pressure release system shall be tested for normal operation before the equipment pressurization reaches the normal working pressure. MEGAJET Flat nozzle high pressure seal at low pressure leakage, when the pressure gradually rises, the leakage situation will stop, the nozzle used for a period of time, if the nozzle slight leakage is normal phenomenon. During pressurization, it should be noted that the short gun operator should be close to and control the short gun overflow valve, and the high pressure pump operator should gradually increase the pressure to make the short gun operator gradually get used to the reaction force brought by the pressurization. M E G A J E T When the surface nozzle works normally, the distance between the nozzle and the cleaning surface can be adjusted (50-100 times of the nozzle diameter according to the difficulty of cleaning the surface dirt).
Sapphire Nozzles
Common Problem Solving
* The nozzle does not rotate First of all, manually rotate the spray head to check whether the interior is rough and difficult to rotate. If it is, the cleaning head must be reinstalled or repaired. If the nozzle starts to rotate but as the pressure rises down or stops rotating, it indicates that the two bearings may be installed in reverse. If there is a blockage, please remove the nozzle and remove the blockage. Do not push the nozzle plug directly into the nozzle body, otherwise it will cause the nozzle to plug again. If none of the above problems appear, the nozzle and nozzle may be installed wrongly. Please check whether the size of the nozzle, the nozzle model and the flow rate are installed correctly according to the subsequent table. * The nozzle rotates too fast Check whether the hexagon screw in the nozzle shell is loose or falls off, causing the deceleration copper sleeve to rotate together with the magnet. If so, tighten the screw or install a new screw, check whether there is oil on the outside of the nozzle, the grease is, does not leak. When the cleaning head lacks grease or rotates, the water seeps into the body, the best practice is to replace the old grease in the shell. Check the shaft core oil seal for damage to prevent grease leakage. If damaged, replace the new oil seal in time. Finally, if the nozzle still rotates at high speed and quickly wears the high pressure seal, check whether the internal deceleration magnet magnetic reduction does not have a deceleration effect.
* Sealed water leakage When the pressure is several thousand psi, the high pressure seal will leak, and the leakage will stop after the pressure gradually rises. If the pressure rises to the working pressure, the seal is still leaking and the high pressure seal needs to be replaced. After replacing the seal and the sealing seat, there is still water leakage in the cleaning head. Please check for scratches on the inside of the shaft core and check the sealing pin for scratches. If there are scratches, please apply for a new sealing needle.
* Seal wear is not too fast Remove the cleaning head and check that the seal seat is properly installed and for scratches or gaps. Check the sealing seat and seal pin and replace the seal seat or seal pin with scratch marks or grooves.
Daily maintenance of products * After the nozzle, it is recommended to operate the cleaned matrix for half a minute. * After the use of the nozzle, it is recommended to blow dry the moisture in the shell with compressed air and dry it for preservation. * Use the nozzle for about 40 hours, grease should be added from copper sleeve wire 324. * During nozzle use, the plane head cover 310 should be replaced when it is badly worn. * During the use of the nozzle, when the lock nut 315 connects the overflow of the single hole overflow, replace the sealing needle connecting the seal 313. * During the use of the nozzle, when the nozzle does not rotate, please check the bearing rotation of the phenomenon, if there is a lag, need to be replaced. * When the nozzle is used, the nozzle is blocked and the outlet line diverges, the nozzle should be cleaned or replaced in time. * During the use of the nozzle, in case of water intake or oil leakage in the rotating body, please replace the upper and lower oil seal of the rotating body in time. * During the use of the nozzle, when the nozzle does not rotate, please check the bearing rotation of the phenomenon, if there is a lag, need to be replaced. During the use of the nozzle, when the nozzle is blocked and the outlet water line diverges, the nozzle should be cleaned up or replaced in time. * During the use of the nozzle, in case of water intake or oil leakage in the rotating body, please replace the upper and lower oil seal of the rotating body in time. * During the use of the nozzle, when the overflow of the eight-hole part of the locking nut 315 affects the pressure seriously, the nozzle should be removed to check whether the high pressure rotary seal 320 is seriously worn, check whether the high pressure sealing seat 319 is seriously deformed, check the contact part of the high pressure sealing pin 312, check whether the high pressure seal part of the rotating shaft 321 is seriously worn or obvious aperture increases, and after the above parts are completed, it should be replaced when necessary * The nozzle overflow port leaks during the nozzle use, and the nozzle connection seal 322 shall be replaced.
Megajet High-pressure waterjetting parts and accessories:
Control Guns
MEGAJET Control guns are a necessity in any hand lancing application. Megajet offers several options from manual to air-actuated, rotary control guns for 20,000psi ~40,000 psi waterblasting. Foot Gun
MegajetFoot Gun is Ideal for a variety of waterblast tube cleaning applications, foot-operated control gun allows the operator to have complete control of the pressure at all times. Custom safety cage and thick blast wall protect operators better than any foot control gun in the industry.
Foot Gun for 40,000psi ( 2758 bar ) Foot Gun for 20000psi ( 1379 bar )
REPLACEMENT CARTRIDGE
Megajet cartridge made from hardened
steel and allows for a complete valve
rebuild quickly and easily for control
guns and foot guns.
High-pressure Hose All high-pressure hoses of Megajet are manufactured to industrial standards and tightly controlled. Compliance with these standards is monitored and ensured by our quality management across the entire production process. Before leaving factory, all hose assemblies are pressure tested in order to guarantee that only products of the highest quality are delivered. All hoses are constructed of a plastic core reinforced with high tensile steel wire and enclosed in a durable, flexible thermoplastic jacket. The smooth plastic core minimizes pressure loss and offers maximum resistance to damage caused by aging, moisture absorption and changing environmental factors. The hoses used for different pressures have different colors, serving as a safety warning.
BYPASS VALVE
A bypass valve diverts a portion of pump flow to a low-pressure outlet and can be used on diesel and electric units. For diesel engines, it is used to prevent bogging of the engine when using flows at the low end of the pump's capability. A bypass valve is required on electric units due to the non-adjustability of motor speed.
PUMP PARTS AND ACCESSORIES
All parts and accessories of high pressure pump are high volumetric efficiency. All pressure-bearing components precision machined from high quality stainless steel.
Uni-Valve STUFFING BOX
ROTARY SURFACE CLEANING TOOLS
MEGAJET ROTARY SURFACE CLEANING TOOLis a rugged, self-powered, rotating tool utilizing up to four straight-pattern, hard-hitting, replaceable sapphire nozzles, rated up to 43,500 psi. The tool rotates in a 360° pattern to provide maximum surface coverage and superior cleaning.
SAPPHIRE NOZZLE for SURFACE CLEANING
High productivity sapphire nozzles for use in the rotary surface cleaning tools; Select nozzles from the charts below by choosing head type, operating pressure, desired flow, and two or four nozzle operation.
){kind=link}